Upgrading Your Roof with Metal Panels

In a recent blog post, we reviewed key considerations to help a building owner decide whether to repair or replace a damaged roof. In this post, we’ll address some ways metal roofing systems are an advantage when upgrading your roof and restoring your building to “like-new”, weathertight condition.

MBCI Blog: Upgrading Your Roof with Metal Panels

Installing Metal Panels Over Existing Roofing

Some owners are concerned about replacing a roof because they dread the cost of removing the existing roof. This concern is valid in many low-slope roofing situations because the new roofing membrane might not be compatible with the existing one, and could cause premature deterioration. There are, however, metal panels specifically designed to be installed directly over existing roofing. And, many of these retrofit systems can be installed over existing roofs made of metal or other materials. Avoiding removal of the old roof obviously saves on cost. However, it also saves considerable time when installing the new roof. As an exposed-fastener metal roofing system, this retrofit application also requires fewer construction components, further streamlining the installation process.

Retrofit metal panels typically feature a membrane treatment that prevents rust or contaminants from the old building materials from transferring to the new panels. This is a versatile solution for both low- and steep-slope roofs (minimum slope: ½:12). It is also very durable and can feature approvals for use in extreme weather locations, including Florida. Metal panels are available in a variety of colors that enhance the overall design of a building. Often, this “replacement metal over existing roofing” approach is the most cost-effective, even compared to some repairs. Additionally, new roofing is more likely be eligible for a warranty, while repairs rarely, if ever, are.

Upgrading Your Roof with Insulated Metal Panels

Energy conservation is on the mind of many building owners and building code enforcement officals. Therefore, adding insulation when upgrading your roof is often required to adhere to building codes. In this case, applying zee-shaped sub-purlins over the existing roof system helps support a new layer of metal roofing. In between the sub-purlins, insulation can be added to meet or exceed current energy code requirements. This system also eliminates the need to remove the existing roofing while providing an added layer (or more) of insulation to improve the overall energy performance of the building. Insulated metal panels (IMPs) like MBCI’s can help keep buildings cooler in summer and warmer in winter—conserving energy year-round.

Sub-purlin systems can fit any existing metal panel, support new panels, and be made to accommodate many types of insulation between the old and new roofs. They can also  support or incorporate a variety of solar energy systems where desired. Roof panel options include variety of profile shapes, textures and colors to suit aesthetic preferences.

Altering the Roof Slope

In some cases, upgrading your roof means changing the roof slope (i.e., turning a low-slope roof into a steeper-sloped roof). In these cases, metal roofing systems can be the most economical choice. Steel framing (16-ga. to 12-ga.) installed over the existing roof frame creates a sloped plane that can support new metal roofing panels. Note that the existing physical shape of the roof, the existing structural system and other rooftop conditions are usually the biggest factors in the geometry and shape of the new roof. Nonetheless, the beauty of the system is that it can dramatically improve the appearance and drainage of a building’s roof, regardless of whether the substrate is steel, wood or concrete.

Lower-slope applications (1/2: to 2:12) are typically driven by economy and designed to efficiently discharge rainwater from the roof. Higher-slope applications (greater than 2:12) often serve to improve and update the look of an existing building. They achieve this by showcasing the metal roof while also improving its drainage and durability. Once the framing is installed, standing-seam metal panels can be installed over the top, creating a ventilated attic space. This allows space for additional insulation , thus improving the energy performance of the building.

Working with Building Professionals

Any of these options are applicable over an existing metal roofing system. They cab also convert other types of roofing systems to longer-lasting metal roofing, or replace an existing roofing system altogether. Of course, engaging the services of a design professional (architect, engineer, etc.) is always appropriate when considering your options. They can help properly assess existing building conditions and recommend the best overall metal roofing solution from metal panel manufacturers.

To learn more about upgrading your roof system with more durable, longer-lasting, better-draining and easier-to-maintain metal roofing systems, contact your local MBCI representative.

Five Retrofit Choices Using Metal Roofing Systems

Buildings usually need new or replacement roofing installed at some point during their service lives. New metal roofing is an ideal roofing retrofit option due to its longevity and durability, which can extend the life of the roofing and require fewer replacements over time. The aesthetic appearance of a new metal roof can also make a notable visual impact to upgrade the building itself.

When considering such a metal roof retrofit on an existing building, the first thing to realize is that there are a number of choices available. Here is a quick look at five of the most common ones that can be selected from and tailored to suit a particular building. Note that since all of them will add some structural loading to the roof, all the retrofit solutions should be reviewed by a professional structural engineer to be sure the existing building can accommodate the changes.

1. Double-Lok® Clip System

When an existing building has an existing PBR roof panel or similar, a Double-Lok® clip and panel system can be installed directly over the existing roof with minimal alterations. In this case, 2″ standoff clips are run from eave to ridge and fastened through the existing roofing panels down into the existing purlins. Then new standing seam metal roofing panels are installed along these clips so they are held 2″ above the purlins and 3/4″ above the major ribs of the existing panel roof. Because of these clearances, the cavity between the old and new roofs can either be vented or additional insulation can be added. Venting the cavity can be a good option when the existing roof slope is 3:12 or greater, as this allows for convective air flow during the summer and can help reduce the chance of ice damming in the winter. For any slopes of 1/2: 12 or greater, adding insulation can improve the overall thermal performance of the building. Generally, this system allows for considerable versatility, even if it takes more parts and labor than some other solutions.

2. Retrofit Roof Panels Over Existing

For cases where a standoff isn’t sought, new, non-structural metal roof panels with a specifically retrofit profile can be installed directly over existing roof panels on roof slopes of 1/2: 12 and greater. That means there is no need to tear out the old roof, since the new panels are through-fastened into the old ones and the purlins below, all in a pattern that avoids the original fasteners. Such retrofit panels are available in 29 and 26 gauge in full range of colors and come with a factory-applied vapor barrier on the underside. Even light-transmitting panels are available for this retrofit panel system.

Retrofit
5 most common choices for retrofit metal roofing systems

3. Notched Sub-Purlins

A variation on the metal-over-metal roofing approach is to use specifically designed z-purlins with notch-outs that are screwed down to the existing purlins. Unlike other systems that run retrofit support members from the eave to the ridge, the notched purlins run parallel to both (in line with existing purlins) with the notches spaced to clear the ribs or corrugations in the existing metal roofing. Profiles are available to match virtually any metal roof produced in the last 50 years. That means they can be installed over existing roofing and, in the process, provide enhanced structural capabilities because of the added sub-purlins.

4. Grid System

When an existing purlin spacing doesn’t meet current code requirements, then the use of crisscrossing hat sections in a grid pattern can provide the additional support needed. Such grid systems are designed to go directly over existing sloped roof systems but many require the use of specific metal roofing panels to work properly.

5. New Framed Roof System

In some cases, a full, steep-sloped roof (greater than 4:12) is sought to be installed over a low-slope roof (1/4:12 – 4:12). In this case, a full metal framing system is available that will create the desired roof slope and transfer the new roof weight to the existing roof deck above the existing roof structural members. As such, the coordination of the new system with the existing roofing, insulation and structure needs to be addressed by licensed engineers. Once designed and installed, an “attic space” will be created by the new retrofit roof system, which should include proper venting in accordance with applicable codes, allowing trapped moisture to escape. It is also recommended that such “attic space” be reviewed by other building, fire, or insurance-related officials for possible sprinkling or extension of existing fire walls to the bottom of the “new” roof system. Regardless, a minimum of 3″ vinyl-faced roll insulation between the retrofit panels and the retrofit purlins will help prevent condensation and roof noise in addition to improving energy efficiency.

To find out more about which retrofit options, or options, are best suited to a particular building that you are involved with, contact your local MBCI representative.

Find a sales representative